solidification range
英
美
网络 固化范围; 凝固温度范围
双语例句
- Casting speed of aluminium alloys can be probably increased by vertical twin-roll thin-strip casting, especially that with large solidification temperature range.
采用立式双辊法可望进一步提高铝合金的浇铸速度，特别是高牌号铝合金的浇铸速度； - Slow cooling is necessary not only in the solidification range but also under the solidification range down to 800 ℃.
慢冷不仅在凝固阶段是必需的，而且在该阶段以下直到800℃。 - Numerical calculation for latent heat releases in alloy castings of any solidification range using an extended temperature-compensation method
采用温度回升法对任意结晶区间的铸件凝固结晶潜热的数值计算 - Directional solidification of TiAl-base alloys using a polycrystalline seed material are studied by using self-made EMCS experiment apparatus with wide range of velocity.
TiAl基合金的籽晶法定向成形实验是在课题组自主设计研制的宽调速电磁成形定向凝固设备上进行的。 - Characteristics Directional Solidification of a Al-Cu Binary Alloy with Wide Freezing Range
宽结晶间隔二元铝合金的定向凝固特性 - A kind of drawing system used in the directional solidification equipment has been introduced, which has a wide speed adjusting range of 0.1~ 83000m/ s and can run very smoothly under low speed end.
本文介绍一种定向凝固设备中使用到的抽拉系统，该系统具有0.1～83000m／s的宽调速范围，且在低速状态下，系统运动平稳。 - A new viewpoint, to apply the equivalent specific heat method on pure metal, eutectic alloys and alloys with narrow solidification range, is put forward with considerations of all possible aspects for emending the temperature down through the solidification range.
提出了把等价比热容法应用到纯金属、共晶合金以及窄凝固区间合金的潜热处理上的观点，并完善了其温度校正方法。 - From the experimental data, the pouring temperature, liquidus and solidus temperatures of the alloy are obtained, and the solidification range of the alloy is determined as 71 ℃.
测试了合金的浇注温度，液相线温度和固相线温度，得出合金的凝固温度区间为71℃。 - It is shown that as local solidification time is 10-1-10-2s, cooling rate of two powders inside the range of-60-+ 320 mesh is 103-104 ℃/ s.
结果表明：两种粉末粒度在-60+320目范围内冷却速度为10~3-10~4℃/s，凝固时间为10~（-1）10~（-2）s。 - A New Understand to Melting Point, Solidification Point and Range of Pattern Waxes
对精铸模料熔点、凝固点、凝固温度区间的再认识 - The processing method for latent heat releases in alloy castings is introduced by the combination of the temperature recovery and the equivalent heat capacity, which can be applied in alloy solidification of any temperature range with the high efficiency.
通过温度回升法与等效热容法的结合，提出了一种能够处理铸件凝固潜热释放问题的方法，它可适用于任意结晶温度区间，且计算效率很高。 - These results proved that solidification range of alloys is not the only factor influencing weld cracking. The physical and chemical properties of ultimate solidification liquid have also an important effect.
这些结果证明，合金凝固范围宽窄不是影响焊接裂纹的唯一因素，最后凝固液体的物理化学性质具有重要作用。 - However, in LFC, dry sand mold is used and the solidification range of common magnesium alloy is broad, which leads grain of castings to be coarse and hence has confined the applications of the magnesium alloy in LFC.
但是消失模铸造所采用的是干砂造型，加之普通的镁合金的凝固范围较宽，导致铸件容易组织粗大，从而限制了镁合金在消失模铸造中的推广应用。 - As the content of particles increased, it widened the solidification temperature range.
随着颗粒含量的增加，使材料的凝固温度区间变长。 - In the aluminum alloy melt solidification process, the outside pressure and the solidification temperature range have some influence on using the pinhole degree rank method to examine the hydrogen content in aluminum alloy melt.
铝合金液凝固过程中，外压及合金的凝固温度范围的大小，对使用针孔度等级法检测铝合金液含氢量有一定影响，外压小时，检测较为精确。